| Table of Contents | ||
|---|---|---|
|
Subsystem version
| Developer | Version | Release date |
|---|---|---|
2020 |
Subsystem Description
| Type | Description |
|---|---|
| Devil ethernet (Low-Level demon) | 689, 699 (Labview 2010) |
| CPU type (Low-Level demon) | Virtual Machine |
| CPU name (Low-Level demon) | vldantedev014 |
| Communication lines | Finuda Moxa Line : 192.168.192.51 (Rack 80) - (SWDAFNE2B porta 11) Kloe Moxa Line : 192.168.192.52 (Rack 77) - (SWDAFNE4B porta 21) |
Programming languages
| Language | Required Add ons/Plugings/Extensions/Libraries |
|---|---|
| LabVIEW 2010 (64-bit) - Low Level Devil | DCS environment, TML Lib (Technosoft Motion Library) |
| LabVIEW 2019 (64-bit) - High Level Interface | DCS environment |
Scrapers Dafne Layout
Hardware Layout
...
Mechanical description
"Encoder" view
| CW | CCW |
|---|---|
Scraper IN
| Scraper OUT
|
"Bolt" view
| CW | CCW |
|---|---|
Scraper OUT
| Scraper IN
|
ATTENTION! All scrapers have a mechanical gearbox (20:1.5); every 20 turns of the axis the Scraper moves by 1.5 mm.
...
Relative movement : positive Steps → Scraper IN
DCS Window description
| Solaris Version | Linux Version |
|---|---|
| built number 20141222 | built number 20200624_rc |
|
|
New features: [ 1 ] "Ctrl On" function [ 2 ] "By Pass" function [ 3 ] "Init" procedures [ 4 ] "Bad communication" indicator |
Operative mode
Before making any movement, it is necessary to put the axis in Operational Mode using the "Oper" key 
.
Oper key (similarly to the magnet control); this operation allows to give current to the phases of the single motor.
It also guarantees safety on any unwanted movements once the set has been found.
"Flags for all elements" allows operation on all axes simultaneously....
To apply the set in the Saved column [mm] to all the axes simultaneously....
End-run
Scraper closed: fully inserted. | |
|---|---|
Devil Description "Dante Control System" (DCS)
...
therefore it has the following MOVXXYNY nomenclature.
Classes: MOV, SER (not implemented; see "Note") Devils : 689, 699 |
|---|
| Note: serial communication is initiated using information from the DEVIL689.system.pref e DEVIL699.system.pref file (/u2/dcs/prefs/devils/ |
DCS MOV Class
Database record
| Satic Fork | Dynamic Fork |
|---|---|
DCS Commands
| DCS Command Name | Parameters | Note | Sub-VI ref. |
|---|---|---|---|
| RESV | - | DCS System | |
| ONLN | - | DCS System | |
| BYPS | ON | OFF | DCS System | |
| PUTT | - | DCS System | |
| EMSK | - | DCS System | |
| CMSG | - | DCS System | |
| INIT | NULL | Performs the initialisation procedure | exeINIT-MOV.vi |
| RESE | NULL | Performs the reset procedure | exeRESE-MOV.vi |
AXPW | ON | OFF | Put the axis on | exeAXPW-MOV.vi |
SETS | #steps , IN | OUT | Moves the axis IN or OUT of the number of steps sent as a parameter | exeSETS-MOV.vi |
SETM | rel [mm] , IN | OUT , abs [mm] | Moves the axis IN or OUT of the millimeters sent as a parameter | exeSETM-MOV.vi |
STOP | NULL | Stops the movement | exeSTOP-MOV.vi |
HOME | NULL | Performs the homing procedure | exeHOME-MOV.vi |
SETE | encoder value [DBL] | Writes the value passed as a parameter to the relative register | exeSETE-MOV.vi |
SETC | counter value [DBL] | Writes the value passed as a parameter to the relative register | exeSETC-MOV.vi |
GENE | [String] | General purpose command | exeGENE-MOV.vi |
DCS Devil prefs
| Key | Value | Comment |
|---|---|---|
| pathFileTable | /u2/dcs/prefs/MOV/setups | at the moment present on Static DBFile |
| MOVClassNumber | 48 | DCS System Class |
| serialType | rs232 | Serial device type rs232,rs422,... |
| boudRate | 115200 | |
| serialSystemType | /dev/ttyS0 | System Resource es. ttyS0,com1,... |
| startUpAxisCicleOnOff | yes | At devil start up put all the axis ON and then OFF |
| startUpAxisOn | no | At devil start up put all the axis ON |
Technosoft IDM module programming
...
ATTENTION! Please, choose IDM240-5EI or IDM640-8EI > STEPPER > OPEN LOOP > With Incremental Encoder, in the picture below.
IDM240-5EI or IDM640-8EI
|
|
|---|---|
| IDM640-8EI model | IDM240-5EI and IDM640-8EI connectors layout |
Analogue and Digital I/O connections
...
We used a standard to easily identify the wiring for the end-run and emergency microswitches.
| Emergency OUT | End Run OUT | Emergency IN | End Run IN |
|---|---|---|---|
| Yellow, Green | White, Grey | Red, Black | Brown, Blue |